If you looked at a 1,000-node site-to-site VPN, which might have 800 or 900 telecommuters in it, that's a million-dollar deal, and it needs good solid management tools.

Jun 28, 2013 · We have a site to site VPN connected with Juniper SSG140 and a 5GT. Both with static IP. Internet Provider Qwest router -> Juniper SSG140 device-> LAN ( Jul 10, 2012 · Type the name of VPN as site-to-site-VPN. Then select predefined button and select P1gateway from the dropdown option. Now click advanced button below. This click will give with following page, Here select Phase 2 Proposal from drop down. Similarly, select Bind to Tunnel Interface and select tunnel.1 and click return. Now click ok. May 28, 2014 · Is it possible to establish site to site VPN between two sites having Dynamic IP. I have had previous experience in creating site to site vpn (using Juniper ssg20) , but i have done it with static IP address on both sites. Currently I have a small setup having : A head office (20 Users) and a small branch office (6 users) . set vpn ipsec site-to-site peer description ipsec set vpn ipsec site-to-site peer local-address 6. Link the SAs created above to the remote peer and define the local and remote subnets. set vpn ipsec site-to-site peer ike-group FOO0 set vpn ipsec site-to-site peer tunnel 1 esp-group FOO0 - Netscreen SIP ALG is disabled Topology: Site A: Netscreen-25 in transparent mode Asterisk server with a public IP address passing through Netscreen-25-- Policy-based site-to-site VPN between A and B --Site B: Netscreen-5 2 x Polycom IP-501 SIP phones each with different extensions. Blue firewall: Juniper SRX 210 (JunOS 10.0R1.8) Red firewall: Cisco ASA 5510 (OS 8.4) This is a script to create a site to site VPN tunnel between a Cisco ASA and a Juniper SRX. Re: Site-to-Site VPN between SSG5 and Cisco ASA 5505 ‎07-07-2015 07:03 PM For Netscreen the proxy ID is only used to bring up the VPN, later it doesnt care about it for passing traffic.

I can see how to setup the VPN server-end, but I am trying to find the documentation to configure the other unit as the "vpn client". In other words, I want the remote end to act as a SOHO router (site-to-site?), putting all the devices behind it on the VPN, instead of having each PC/device have to run their own VPN client software.

Apr 28, 2013 · VPN diagram - https://dl.dropbox.com/s/chyy91kejm4lxsw/VPN%20network%20diagram.png Juniper1 config https://dl.dropboxusercontent.com/s/gddaxh4yfdr2hnh/Junipe Site to Site VPN Between Netscreen 25 and Cisco 837 Even though this is damn old topic that Google provided me a link to based on querying " Info Notify message requeue retry counter exceeded sa" today.. Jan 29, 2020 · Firewall LAN-to-LAN Route-Based VPN articles. Firewall LAN-to-LAN Policy-Based VPN articles. Configuring a VPN between a Juniper Firewall device and a 3rd Party Device . Client-to-LAN. Configuring a Juniper Dial-Up / NetScreen-Remote VPN. Configuring PPTP, IPSec Pass-through or L2TP over IPSec solutions on a Juniper Firewall device The section below which is highlighted in bold shows the status of the vpn tunnel (left) and the status of the VPN monitor (right). In this case the VPN tunnel is active and the VPN monitor is dashed out as it isnt enabled. netscreen(M)-> get sa | i [peer ip] 00000007< [peer ip] 500 esp:3des/md5 zbcA14zz 3317 unlim A/- 22 0

NetScreen Configuration: Site-to-Site VPN The basic steps on the NetScreen side to create the dial-up VPN consist of three steps: create the IKE gateway, create the autokey IKE VPN, and add policies. Since it's difficult to go over the steps needed in the web-UI, I'll outline the CLI commands that are needed.

Using the same firewall, VPN, and DoS mitigation technology as NetScreen's high-end central site products, the NetScreen-5GT is fully capable of securing a remote office, retail outlet, or a broadband telecommuter. In this post, we will describe how to configure VPN site-to-site in netscreen devices. The screen OS used is 6.3.X The connection it will be secured throw VPN tunnel between servers and